Mar 15 2011

Making a toboggan

Published by at 4:12 am under Expeditions and Experiences

This is one of the major projects I´ve been working on this winter. I did use some more specialized metal tools for the process so I hope it doesn´t spoil the primitive character of this website ;-). I decided to write about the process in a how-to format, with some of my own experiences and observations added in italics.


Toboggans and snowshoes were the major form of winter transportation for the Ojibway, the Native people of the Great Lakes area. Toboggans tend to be fairly narrow (one foot or less in width, about 30cm) so they follow well in a snowshoe trail and have an upturned front so that they don´t dig into the snow.

The process

The first step consists in selecting the right wood – it needs to be strong, flexible and preferably also light. One of the best species for that purpose that grows in the Northwoods is white ash (shown in the picture above), which is the wood I´ve used for my toboggan. Selecting the right tree is another important decision: The wood should be as straight-grained and knot-free as possible. Any knots are a potential weak spot and are difficult to flatten out. Wood splits along the path of least resistance, and if the grain is twisted the split will follow those curves.

The two-plank toboggan is the most common style and the one which I will describe here, although it is also possible to just use one very large board or more than two planks (the latter tends to make it less stable though). The tree size needs to match accordingly – if a one foot wide toboggan is desired, it follows that each of the two planks has to be at least 6 inches wide, so the trunk of the cut tree will most likely be somewhat bigger.

The tools I used for the process are as follows: A heavy axe and saw for cutting down the tree and splitting the log sections, a hewing axe and a drawknife for thinning down the planks and a knife. For the steaming process I used a large metal pot.

Once the tree is felled and cut into smaller sections, the log needs to be split in half. An axe can be used to form the initial split through the center on one end of the tree and then a wedge gets inserted to widen the crack. Wedges are easily made from the side branches of the felled tree.

As the crack progresses in length, additional wedges can be inserted and then pounded in with a mallet or the back of an axe. It is recommendable to do this on both sides simultaneously so that there is less of a chance for the crack running off to one side.

Sometimes you learn those lessons the hard way: When I got to the center part of the log, the split ran off to the side and both split pieces ended up not being useable for a toboggan since they were too short. Fortunately I still had a few more log sections.

By adjusting where and at which angle the wedges are placed one can somewhat change the direction of the crack, but as mentioned before, the crack tends to follow the path of least resistance – along the grain.

Even under ideal conditions the split will probably not be totally straight and flat, so the next task is to figure out where to get a flat side while using the maximum width available in the log (as close to the center/split as possible). The plank to the right in the picture above has a string running along its length to mark a straight line which will be used to form one of the flat sides of the toboggan. A hewing axe is ideal for the rough work, and a drawknife helps to get the surface more flat and smooth. Once a flat side is established (left board in the picture), the thickness of the planks can be marked by running a line parallel to the flat side. Now the planks are ready to be thinned down. It is advisable to proceed in small step, i.e. not go to the final thickness right away in case a cut goes a little too deep or an adjustment needs to be made.

I decided to first work the plank down to a thickness of ½ inch (about 6mm), with the final thickness being ¼ inch. White ash is plenty strong and I figured that a board on the thin side would be easier to steam-bend while also being lighter. Many toboggans are in the thickness range of ¼ – 3/8 inches.

Once the planks are thin and smooth they need to be laid next to each other to determine the sides which will adjoin. Some trimming may be necessary in order for the planks to fit together without major gaps in between. Crosspieces will ultimately hold the two planks together, and marking where they will go on the toboggan is the next step. I recommend having a crosspiece every foot or less along the length of the toboggan. A smaller log section can be used to split out the rough crosspieces, which then get carved and fitted with holes and a notch at each end (on the underside as shown on the picture above – this is where the gear lashing cord will run through). The holes on the toboggan planks need to be lined up with the ones on the crosspieces.

I used 10 crosspieces for my toboggan, and each crosspiece had 12 holes placed in a diagonal pattern. After all the crosspieces were done, I laid them on the boards and poked through the individual holes with an awl so that the holes on the planks would be marked in the same spot.

The traditional toboggan style has a fairly strong bend in the front to prevent it from digging into the snow. There are several ways to achieve that bend, with steam-bending being the most common used nowadays. Under more primitive circumstances, the most effective method is to pre-soak the planks in water and then boil them (at least the section that receives the bend). The time required for sufficient boiling depends on the thickness of the planks, how dry they were to begin with and how long they were soaked before. A cooking vessel could be e.g. a hollowed out log or a dugout canoe filled with water which gets heated up with hot rocks.

For boiling the planks, I used a large steel pot. The bottom got immersed in hot water, but the area where the bend was going to be was too high up to be submerged so I poured hot water over the spot for a few minutes.

When the planks are hot and thoroughly saturated with water they can be bent around a rounded stationary pole or log. With the front pinched between a couple logs, one can get quite a bit of leverage by working from the back of the plank. I suggest to initially be careful with the bending to get a feel for how much force needs to be used. If it seems hard to achieve any bend, the planks might not be saturated enough with water and/or not hot enough – more boiling/heating may be required.

Apparently in my case the steaming process wasn´t thorough enough so the plank started bending mostly in a weak spot with a branch hole. I therefore decided to concentrate the bend on two spots on the planks and work with less of a curve than some of the old-style toboggans.

Rawhide lashing is used to secure the crosspieces on the planks (a set of two diagonally placed holes gets tied with a short piece of rawhide). The pulling cord is also made of rawhide – a braided rope works pretty well since it´s quite flexible.

The final works were done by the firelight inside of a wigwam. I thinned down the tip of the rawhide lashing to fit it through the holes; sometimes a needle was also helpful in that process.

Details of the rawhide lashing. From top to bottom: A bundle of dried rawhide, braided 3-ply rawhide string for the pulling cord, and reverse wrapped rawhide that runs along the sides of the toboggan (gear lashing cord).

Greasing the underside of the toboggan helps to protect it from moisture, especially in wet snow.

For this I chose a fat with a high melting temperature (tallow) since it forms a coat that allows the toboggan to glide over snow and ice. The picture also shows how the rawhide lashing for the crosspieces is sunken into the boards in order to avoid abrasion. Also visible is the radical bend in one part of the upturned front.

The finished toboggan is 7feet 6 inches long (about 2.3 meters) and between 13in (33cm) in the front and 11.5in (29cm) in the most narrow spot towards the back (the planks aren´t totally rectangular). Also visible is the gear lashing cord to the sides and the pulling cord in the front.

As you may see in the picture, the bend in the front isn´t equally distributed – it is concentrated in two spots (which makes it somewhat weaker than a nicely bent arch).

Toboggan with gear lashed on. Simple rawhide lashing is tied across the load and lashed to the gear lashing cords to the sides.

The planks turned out to be slightly thicker in the center than on the sides which meant that the crosspieces weren´t flush with the boards. I therefore wrapped the gear lashing cord around the crosspieces instead of just fitting it underneath the notch.

Concluding thoughts:

It´s been a rewarding process for me. The resulting toboggan may not be a work of art, but it´s pretty sturdy and functional. Specialized metal tools like a hewing axe and a drawknife make the process much faster and easier than working with basic tools such as axe and knife. With stone tools only this would be an even more daunting project, and probably only realistic if a wood is chosen that´s easy to work with stone tools (such as Atlantic White Cedar, since it splits easily and therefore reduces the amount of wood that needs to be removed). The research I´ve done and my own experience tell me that most northern Natives probably used hide sleds/toboggans before metal tools were available to them. I may work on a simple hide sled in the near future and post about it here.

Drilling the holes to lash on the crosspieces with a knife took up a lot more time than I originally thought. I experimented with drilling holes with a thin bow drill set which is even more time-consuming (white ash is a pretty hard and dense wood). Reducing the amount of holes may help here – by using less crosspieces or notching the crosspieces so the rawhide can go around them rather than through holes.

If other people have worked with making toboggans or similar crafts with hand tools, I´d be happy to hear about your experiences and suggestions! Also, I´m trying to improve this tutorial so it may be easier to understand for someone who´s fairly new to this…any comments and suggestions are welcome.

Many of the details of the toboggan have been inspired by Jarrod Stone-Dahl, a talented craftsman from northern Wisconsin. You can check out his website here.


Get my book "Traditional Trout Fishing: Fishing for Survival in the North (Volume 1)

9 responses so far

9 Responses to “Making a toboggan”

  1. Coureurdeboison 16 Mar 2011 at 2:27 am

    Hello Torjus Gaaren,

    Very nice tobogan, is that a poplar tree and is it the best wood to use ? Cedar would be nice to split too.

    I would like to ask you if you have some more pictures on your beaver tooth knife, I am a beaver trapper and I am also very passionate about primitive tools, If i’ve well understood, the teeth should only be an inch or less longer than the wood so it won’t split or break ? And you always use the tip of the tooth to work with noth the sides ? I’ve visited a couple of native american museums but none had any precise information on this subject.

    Thanks !!! keep up the great work,

    Btw, i just signed up to your site and facebook nice posts.

  2. Deus Ex Machinaon 16 Mar 2011 at 2:42 am

    Nice work, Thomas. I’ve found that my “first” of anything leaves something to be desired. Functional is good, but I think you are being a bit modest.

  3. Torjuson 16 Mar 2011 at 4:56 pm

    Steve, it’s Thomas who has written this article.

  4. Thomason 17 Mar 2011 at 2:42 am


    thanks for the feedback.

    @Steve: I guess it can be confusing with both Torjus and I writing now…
    If you´re interested in knowing more about it, I suggest checking the header and the “About us” column. Torjus also recently posted about some website changes…

    The toboggan is made out of white ash (you can see one in the first picture of the arcticle). I agree, cedar would split pretty nice too, although that could also be a disadvantage: Planks made of cedar that are that thin are more likely to split when they experience some stress, e.g. bumping against a stump or rock. It sure would make the construction faster though…

    For the beaver tooth knife you need to ask Torjus, I haven´t made one myself yet…

    @Deus Ex Machina: That´s my experience too – the first attempt may sometimeslook a little crude, but I guess that´s how we learn…

    Modesty…you have a good point there. I personally draw a lot of inspiration from various native cultures that practise “modesty”, sometimes in extreme ways, such as when the best hunter comes back with a lot of meat and gets ridiculed by his clan for daring to bring such a nasty carcass back (!Kung San)…or some northern tribes where hunters used to boast about their “embarrasing” hunting skills. Helps to keep the ego in check 🙂 On the other hand, it may be good to call things for what they are…

  5. Maton 19 Mar 2011 at 2:06 am

    Many thanks for the tutorial! A toboggan and snowshoes are certainly essential item for any kind of winter travel in my area. I do have some questions regarding the board making process. After the log is split in half, is the rest hewn away towards the center to make the board or more splits are made after the initial split? Also wondering if the wood needs to dry out for any length of time to avoid checking and warpage. Although that probably should not cause much problem with given dimensions.
    Anyways I enjoyed your tutorial, it gives me inspiration to at least give it a go sometime in the future… And I’ll be sure to do research on hide sleds also(never heard of them), to maybe avoid frustration and wasting good wood while trying to make a wooden toboggan.:)

  6. Thomason 20 Mar 2011 at 2:25 am

    Hey Mat,

    glad to hear you enjoyed the tutorial, and that it i may be helpful to you.
    You bring up some good questions that help me to see where I could inlude more information or clarify more so that someone who hasn´t made a toboggan before understands the whole process…

    Once the log is split down, you basically just need to determine where your plank(s) will be located within each one of the split halves (in general as close to the center split as possible since that´s where you have the widest section). After that it´s bascially hewing down the plank to its final dimensions as you said,no further splitting required.
    Now in some cases – if you select a very large tree – you could potentially get more than one plank out of each half and then you could potentially split it into more sections. I don´t think I would recommend that to a novice though (or to cut such a big tree to begin with) – if the split runs off now, then you may end up with two pieces of which neither one works for a toboggan plank.

    You can start splitting the wood right away (still green) and work it down to plank thickness. In that case I suggest drying the wood slowly in a cool and dark place, otherwise you may end up with cracks and warping. The slower it dries the better. If the wood is already dry you don´t have to worry about that.

    I haven´t found much information about hide sleds myself (other than some historical account that mention them being used by Natives before they made wooden toboggans with steel tools), so if you do find some good sources, let me know…

  7. jackon 15 Jan 2014 at 9:23 pm

    ausome toboggan

  8. Kastela Croatiaon 31 May 2014 at 10:17 am

    Am very glad to see such a useful post. I also write on my own blogs and can really say thx for updating your blog

  9. overwatch junkrat pornon 13 Dec 2018 at 4:53 am

    Are you a Mercy most important who hardly ever achieves glory?

Trackback URI | Comments RSS

Leave a Reply

You must be logged in to post a comment.